Audi Q3 Owners & Service Manuals

Audi Q3: Seat Side Trim on the Tunnel Side, Removing and Installing

Body Interior / Body / Audi Q3 (8U) 2011-2018 Service Manual / Seat Side Trim on the Tunnel Side, Removing and Installing

Removing

  WARNING

  • Follow all safety precautions when working with pyrotechnic components. Refer to → Chapter "Pyrotechnic Components Safety Precautions".
  • Before handling pyrotechnic components (for example, disconnecting the connector), the person handling it must "discharge static electricity". This can be done by touching the door striker, for example.

- Move the front seat all the way up.

- Remove the front seat. Refer to → Chapter "Front Seat, Removing and Installing".

- Fasten the front seat on the Engine/Transmission Holder - Seat Repair Fixture -VAS6136-. Refer to → Chapter "Front Seat, Mounting on Fixture for Seat Repair".

- Remove the expanding rivet -2- from the tunnel side seat side trim.

- Release the tab -arrow A- and pull the trim -1- outward -arrow B-.

- Remove the backrest hinge side trim on the tunnel side in direction of -arrow C-.

Audi Q3. A72-10984

Installing

  WARNING

  • Follow all safety precautions when working with pyrotechnic components. Refer to → Chapter "Pyrotechnic Components Safety Precautions".
  • Before handling pyrotechnic components (for example, connecting the connector), the person handling it must "discharge static electricity". This can be done by touching the door striker, for example.
  • Observe all measures when installing the front seat. Refer to → Chapter "Front Seat, Removing and Installing".

Install in reverse order of removal.

Installation notes, for example tightening specifications, replacing components. Refer to → Chapter "Overview - Seat Pan, Sill Panel/Tunnel Side Seat Side Trim on Manual Front Seat".

Drawer Mount, Removing and Installing

Removing

- Remove the sill panel side seat side trim with the bracket.

  • Standard seat. Refer to → Chapter "Seat Side Trim on Sill Panel Side, Removing and Installing, Manual Front Seat".
  • Folding seat. Refer to → Chapter "Seat Side Trim on Sill Panel Side, Removing and Installing, Passenger Folding Seat".

- Move the front seat all the way to the rear and then into its highest position.

- Remove the drawer -1- until stop from the drawer mount -arrow-.

- Carefully push the right and left release tab -3- toward the outside with a screwdriver and at the same time remove the drawer completely from the mount.

- Remove the bolts -4-.

- Disengage the drawer mount -2- from the mounts in the seat frame and remove.

Audi Q3. A72-11513

Installing

Install in reverse order of removal.

Installation notes, for example tightening specifications, replacing components. Refer to → Chapter "Overview - Seat Pan, Drawer".

Storage Compartment, Removing and Installing

Removing

  WARNING

  • Follow all safety precautions when working with pyrotechnic components. Refer to → Chapter "Pyrotechnic Components Safety Precautions".
  • Before handling pyrotechnic components (for example, disconnecting the connector), the person handling it must "discharge static electricity". This can be done by touching the door striker, for example.

- Remove the front seat. Refer to → Chapter "Front Seat, Removing and Installing".

- Fasten the front seat on the Engine/Transmission Holder - Seat Repair Fixture -VAS6136-. Refer to → Chapter "Front Seat, Mounting on Fixture for Seat Repair".

- Open the storage compartment -1- and remove the bolts -2-.

Audi Q3. A72-11560

- Release the tab -arrow- on the storage compartment -2- and remove the storage compartment downward from the sill panel seat side trim -1-.

Audi Q3. A72-11561

- Push the storage compartment -1- in direction of -arrow- and disengage the retainer -lower arrow- from the upper seat frame -2-.

- Remove the storage compartment from the seat pan upper frame.

Audi Q3. A72-10810

Installing

  WARNING

  • Follow all safety precautions when working with pyrotechnic components. Refer to → Chapter "Pyrotechnic Components Safety Precautions".
  • Before handling pyrotechnic components (for example, connecting the connector), the person handling it must "discharge static electricity". This can be done by touching the door striker, for example.
  • Observe all measures when installing the front seat. Refer to → Chapter "Front Seat, Removing and Installing".

Install in reverse order of removal.

Installation notes, for example tightening specifications, replacing components. Refer to → Chapter "Overview - Seat Pan, Storage Compartment".

READ NEXT:

  Seat Depth Adjuster, Removing and Installing

Special tools and workshop equipment required Trim Removal Wedge -3409- Removing   WARNING Follow all safety precautions when working with pyrotechnic components. Refer to â†

  Backrest Release, Removing and Installing

  Note Release is only on front passenger side folding seat. Removing - Remove cap -2- using screwdriver. - Open the tabs with a screwdriver -arrows- and remove the release le

  Overview - Bench Seat/Single Seat

1 - Front Mount For securing the rear bench seat Welded to the floor panel. 2 - Cover For child seat anchor Quantity: 4 Removing and installing. Refer to →&n

SEE MORE:

  Text input

Fig. 17 Center display: text input diagram with MMI Navigation plus 1/ MMI Radio plus 2 Overview In the input fields of the various menus, you can enter letters, numbers, and characters, for example to find a contact in the directory. The text input display 1 or 2 depends on the vehicle equipment.

  Parking aid plus

Activating and deactivating Applies to: vehicles with parking aid plus Fig. 111 Center console: parking aid button General information The parking aid assists when parking and maneuvering by providing warnings about obstacles. If the ultrasonic sensors on the vehicle fig. 88 detect an obstacle, th

© 2019-2026 Copyright www.auq3.net | 0.0111