Audi Q3 Owners & Service Manuals

Audi Q3: Steering Column Electronics Control Module Connector Assignment

Audi Q3 (8U) 2011-2018 Service Manual / Electrical System / Electrical Equipment / Exterior Lights, Switches / Steering Column Electronics Control Module Connector Assignment

Steering Column Electronics Control Module -J527- Connector Assignment, with Mechanical Ignition Lock

  • The Steering Column Electronics Control Module -J527- is part of the complete system "steering column switch module". It receives the signal for example from the steering column switch.
  • Check the Steering Column Electronics Control Module -J527- in "Guided Fault Finding". Refer to Vehicle Diagnostic Tester.

Audi Q3. Steering Column Electronics Control Module -J527- Connector Assignment, with Mechanical Ignition Lock

A - Steering Wheel Connector Mount

1 - Not assigned

2 - Not assigned

3 - Driver Airbag Igniter -N95-"+"

4 - Driver Airbag Igniter -N95-"-"

5 - Not assigned

6 - Not assigned

7 - Ground

8 - Cruise control system "On, Off"/horn-signal

9 - LIN bus

10 - Terminal 15 multifunction steering wheel

11 - Not used

12 - Not used

B - Vehicle Electrical System Connector Mount

1 - Voltage supply terminal 30

2 - Voltage supply terminal 31

3 - Comfort CAN bus Low

4 - Comfort CAN bus High

5 - Cruise control system "On, Off"

6 - Terminal 50

7 - Terminal S

8 - Not assigned

9 - Not used

10 - Not used

11 - P locking mechanism

12 - Powertrain CAN bus Low

13 - Powertrain CAN bus High

14 - Terminal 15

15 - Not used

16 - Not used

C - Ignition Lock Connector Mount

1 - Ignition/Starter Switch Ground

2 - Ignition/Starter Switch Charge

3 - Terminal 15

4 - S

5 - Terminal 50

6 - Terminal 30

D - Vehicle Electrical System Airbag-Connection Connector Mount

3 - Driver Airbag Igniter -N95-"+"

4 - Driver Airbag Igniter -N95-"-"

5 - Not assigned

6 - Not assigned

Steering Column Electronics Control Module -J527- Connector Assignment, with Electronic Ignition Lock

  • The Steering Column Electronics Control Module -J527- is part of the complete system "steering column switch module". It receives the signal for example from the steering column switch.
  • Check the Steering Column Electronics Control Module -J527- in "Guided Fault Finding". Refer to Vehicle Diagnostic Tester.

Audi Q3. Steering Column Electronics Control Module -J527- Connector Assignment, with Electronic Ignition Lock

A - Steering Wheel Connector Mount

1 - Not assigned

2 - Not assigned

3 - Driver Airbag Igniter -N95-"+"

4 - Driver Airbag Igniter -N95-"-"

5 - Not assigned

6 - Not assigned

7 - Ground

8 - Cruise control system "On, Off"/horn-signal

9 - LIN bus

10 - Terminal 15 multifunction steering wheel

11 - Not used

12 - Not used

B - Vehicle Electrical System Connector Mount

1 - Voltage supply terminal 30

2 - Voltage supply terminal 31

3 - Comfort CAN bus Low

4 - Comfort CAN bus High

5 - Cruise control system "On, Off"

6 - Not assigned

7- Not used

8 - Not used

9 - Not used

10 - Not used

11 - Not used

12 - Powertrain CAN bus Low

13 - Powertrain CAN bus High

14 - Not used

15 - Not used

16 - Electronic steering column lock "Locking possible"

C - Not Assigned

D - Vehicle Electrical System Airbag-Connection Connector Mount

3 - Driver Airbag Igniter -N95-"+"

4 - Driver Airbag Igniter -N95-"-"

5 - Not assigned

6 - Not assigned

Steering Lock Housing, Removing and Installing

Special tools and workshop equipment required

  • 7/16 Inch Extractor -T10424US-

Removing

- Remove the steering column switch module. Refer to → Chapter "Steering Column Switch Module, Removing and Installing, with Mechanical Ignition Lock".

- Disconnect the connectors -1 and 4-.

- Remove the shear bolt -2- using the 7/16 Inch Extractor -T10424US-.

- Remove the steering lock housing -3-.

  Note

If the shear bolt cannot be removed using the 7/16 Inch Extractor -T10424US-, use an angled hand drill and 8.5 mm diameter bit to drill it out.

To replace the steering lock housing, the ignition/starter switch and lock cylinder must be removed.

  • To remove the ignition/starter switch. Refer to → Chapter "Ignition/Starter Switch, Removing and Installing".
  • To remove the lock cylinder. Refer to → Chapter "Lock Cylinder, Removing and Installing".

Audi Q3. A94-11101

Installing

Install in reverse order of removal. Note the following:

- Tighten the new bolts -arrows- until the head shears off.

- Install the steering column switch module. Refer to → Chapter "Steering Column Switch Module, Removing and Installing, with Mechanical Ignition Lock".

Audi Q3. A94-11113

    READ NEXT:

     Overview - Parking Aid

    In the Front of the Vehicle 1 - Right Front Parking Aid Sensor -G252- In the front bumper cover Removing and installing. Refer to → Chapter "Front Parking Aid Sensor, Remov

     Parking Aid Control Module -J446-, Removing and Installing

      Note On vehicles with parallel parking assist the Parallel Parking Assistance Control Module -J791- is integrated in the Parking Aid Control Module -J446-. - If replacing the contr

     Front Parking Aid Sensor, Removing and Installing

    Front Parking Aid Sensors, Removing and Installing, through MY 2014 Right/Left Front Parking Aid Sensor -G252-/-G255- Special tools and workshop equipment required Hook Tool -T40207- Removi

    SEE MORE:

     Correct safety belt positioning

    Fig. 58 Lap/shoulder belt positioning Fig. 59 Safety belt positioning for pregnant women Fastened safety belts only offer optimal protection during an accident and reduce the risk of serious injury or death when they are positioned correctly. Furthermore, the correct safety belt position holds the

     Wheel Bearing Housing, Removing and Installing

    Wheel Bearing Housing, Removing and Installing, FWD Vehicles Special tools and workshop equipment required Torque Wrench 1332 40-200Nm -VAG1332- Removing - Measure dimension from center of wheel to lower edge of wheel housing. Refer to → Chapter "Wheel Bearing in Curb Weig

    © 2019-2024 Copyright www.auq3.net