Molded Foam Part, Removing and Installing, Audi Q3 through MY 2014
Removing
- Remove the front bumper cover. Refer to → Chapter "Bumper Cover, Removing and Installing".
- Guide the molded foam piece -2- at the top out of the bracket -arrow- and at the bottom out of the holder -1-.
Installing
Install in reverse order of removal. Note the following:
- Install the front bumper cover. Refer to → Chapter "Bumper Cover, Removing and Installing".
Molded Foam Part, Removing and Installing, Audi Q3 from MY 2015
Removing
- Remove the front bumper cover. Refer to → Chapter "Bumper Cover, Removing and Installing".
- Release the retainer -1-, rotate the molded foam part -2- out and remove downward from the bracket -3-.
Installing
Install in reverse order of removal.
Molded Foam Part, Removing and Installing, Audi RS Q3
Removing
- Remove the front bumper cover. Refer to → Chapter "Bumper Cover, Removing and Installing".
- Release the catch -3- and disengage the molded foam part -2- from the radiator grille -1-, to do this pivot the upper molded foam part out of the mount -4- in the direction of the -arrow-.
Installing
Install in reverse order of removal. Note the following:
- Install the front bumper cover. Refer to → Chapter "Bumper Cover, Removing and Installing".
Molded Foam Part Mount, Removing and Installing, Audi RS Q3 through MY 2014
Removing
- Remove the license plate.
- Remove screws -2- and -3- on the license plate holder -1-.
- Remove the molded foam part. Refer to → Chapter "Molded Foam Part, Removing and Installing, Audi RS Q3".
- Remove the bolts -arrows-.
- Remove the mount -1-.
Installing
Install in reverse order of removal. Note the following:
- Install the molded foam part. Refer to → Chapter "Molded Foam Part, Removing and Installing, Audi RS Q3".
Molded Foam Part Mount, Removing and Installing, Audi RS Q3 from MY 2015
Removing
- Remove the radiator grille reinforcement brace. Refer to → Chapter "Reinforcement Brace, Removing and Installing, Version 2".
- Remove the molded foam part. Refer to → Chapter "Molded Foam Part, Removing and Installing, Audi RS Q3".
- Remove the mount -1-.
Installing
Install in reverse order of removal.
Headlamp Washer System Spray Nozzle Cover, Removing and Installing
Removing
- Pull the spray nozzle telescope -2- until stop out of the bumper cover -arrow A-.
- Hold telescoping section in the extended position with pliers.
- Spread the side pieces -3- of the cover -1- for the spray nozzle -arrow B- and carefully disengage from the pins and remove.
Installing
Install in reverse order of removal. Note the following:
- Press the spray nozzle cover on until it engages audibly.
READ NEXT:
Air Intake Grille Trim, Removing and Installing
Removing
- Remove the air intake grille. Refer to
→ Chapter "Air Intake Grille, Removing and Installing, Vehicles
through MY 2014".
- Remove the front bumper cover. Refer to
â
Side Air Intake Trim, Removing and Installing, Audi RS Q3 through MY 2014
Removing
- Left: remove the front bumper cover. Refer to
→ Chapter "Bumper Cover, Removing and Installing".
- Right: remove the front wheel housing liner and wheel
spoiler. Refer
RSQ3 Spoiler-Lower Section, Removing and Installing
Removing
- Remove the lower radiator grille. Refer to
→ Chapter "Radiator Grille, Removing and Installing, Audi RS Q3
through MY 2014".
- Remove the bolt -arrow-.
- ReleaseSEE MORE:
Introduction
Applies to: vehicles with telephone
You can operate various telephone functions easily
through the MMI in your vehicle.
Depending on the country and the vehicle equipment,
the following options may be available:
Connecting a cell phone with Bluetooth
Using two telephones
Using the Audi phone bo
Overview - Infotainment System
MMI Navigation Plus, 7T6
Information Electronics Control Module 1 -J794- with DVD
player/SD card reader/navigation system integrated in the
instrument panel
Internal hard drive memory (HDD) for storing navigation data
and MP3 files
Integrated control
Front Information Display Control