Audi Q3 Owners & Service Manuals

Audi Q3: Component Overview - Run-Flat Tire (PAX)

Wheel and Tire General Information / Chassis / Audi Q3 (8U) 2011-2018 Service Manual / Component Overview - Run-Flat Tire (PAX)

  Caution

It is mandatory for run-flat tires to have a tire pressure monitoring system in the vehicle.

  Note

  • Be careful not to scratch off the glued- on wheel trim on these rims.
  • The surface of the wheel trim is very sensitive.
  • The rim will have be replaced if the wheel trim is damaged.
  • The wheel trim cannot be replaced.

Audi Q3. A44-10265

Audi Q3. Component Overview - Run-Flat Tire (PAX)

1 - PAX Tires

2 - Support Ring

3 - Wheel for PAX Tires

  • Note assembly instructions. Refer to → Chapter "Wheel, Changing and Mounting"

4 - Wheel Electronics

  • Batteries must be completely replaced.
  • Remaining battery life, temperature and pressure can be read via diagnosis with Vehicle Diagnostic Tester.

Beru wheel electronics system. Refer to → Chapter "Wheel Electronics System (Tire Pressure Monitoring System), Beru ".

Siemens wheel electronics system. Refer to → Chapter "Wheel Electronics System (Tire Pressure Monitoring System), Siemens ".

5 - Metal Valve Body

  • Only install valve according to Parts Catalog
  • Delivered complete

6 - Wheel Bolt

  Note

Make sure the correct wheel bolts are installed. Refer to the Parts Catalog.

  • Note assembly instructions. Refer to → Chapter "Wheel, Changing and Mounting"
  • Anti-theft wheel bolts. Refer to → Fig. "Anti-Theft Wheel Bolts"
  • Refer to → Chapter "Wheel Bolt Tightening Specifications"

7 - Wheel Bolt Adapter

  • Place on wheel bolt designed for it. Refer to → Fig. "Anti-Theft Wheel Bolts"

8 - Cap

  • Place on wheel bolt

9 - Wheel Bolt, Two-Part

  • Note assembly instructions. Refer to → Chapter "Wheel, Changing and Mounting"
  • Refer to → Chapter "Wheel Bolt Tightening Specifications"

10 - Cap

11 - Wheel Bolt Cover Cap

12 - Adhesive Balancing Weights

  • Maximum 60 grams per rim permitted
  • Clean wheel where it will be adhered so it is free of dirt and grease
  • Remove protective film
  • Attach balance weights to intended surfaces

READ NEXT:

  Wheel, Changing and Mounting

Special tools and workshop equipment required Torque Wrench 1332 40-200Nm -VAG1332- Wheel Lock Set -T10101- Wheel Lock Set -T10101A- Wheel Lock Set -T40004- Wheel Lock Set -T40073- Wax

  Installation Instructions, Run-Flat Tires

Warm up cold tires to the minimum mounting temperature   Note This applies also to ultra high performance tires (height-/width ration smaller/same 45% and speed rating symbol larger than/

  Removing Tires, Run-Flat Tires

  Note Be careful not to scratch off the glued- on wheel trim on these rims. The surface of the wheel trim is very sensitive. The rim will have be replaced if the wheel trim is damage

SEE MORE:

  Menus and symbols

Fig. 14 MMI: center display Description of common symbols You can operate the default functions using the symbols that follow. The symbols may be found in any menu, depending on the context. Go back one level Close the menu Search for content Open explanations for a menu Open settings for the

  General Information

Before beginning balancing, the following requirements must be fulfilled. Tire inflation pressure must be OK. The tire tread must not be worn down on one side and should be at least 4 mm deep. The tire must not have any flat spots. It is not possible to balance a flat spot. The ti

© 2019-2026 Copyright www.auq3.net | 0.0115