Audi Q3: Component Location Overview - Relay Carriers, Fuse Panels and E-Boxes
Overview - E-box, Wire Junction, Fuse Panel, Suppressor
1 - Nut
- 9 Nm
2 - Wiring Harness
3 - Nut
- 4.5 Nm
4 - Suppressor -C24-
- Removing and installing. Refer to → Chapter "Suppressor -C24-, Removing and Installing".
5 - Bracket
- For the suppressor.
6 - Relay
- Equipment level
- Allocation. Refer to → Wiring diagrams, Troubleshooting & Component locations.
7 - Relay carrier under the E-box
- Equipment level
- Allocation. Refer to the Parts Catalog.
- Removing and installing. Refer to → Chapter "E-Box, Removing and Installing".
8 - Nut
- 3 Nm
9 - Cover
- For the plenum chamber connector station
- Removing and installing. Refer to → Chapter "Plenum Chamber Connector Station Cover, Removing and Installing".
10 - Nut
- 3 Nm
11 - Body
- To the vehicle interior
12 - Screw
- 2.4 Nm
13 - 40-Pin-Connector
- Removing and installing. Refer to → Chapter "E-Box, Removing and Installing".
14 - Cover
- for E-box
15 - Relay and Fuse Panel B -SB-
- with Fuse Panel A -SA-
- Removing and installing. Refer to → Chapter "Relay and Fuse Panel B -SB- in the E-Box, Removing and Installing".
16 - Bolt
- 9 Nm
- With permanent relay and Fuse Panel B -SB-
17 - Nut
- 6 Nm
18 - E-Box
- Removing and installing. Refer to → Chapter "E-Box, Removing and Installing".
19 - Cable Holder
20 - Mounting Box - Upper Section
- For the suppressor.
21 - Mounting Box - Lower Section
- For the suppressor.
22 - Anti-Twist Mechanism
- For the wire eye
Tightening Specifications Fuse Panel A -SA- on the Left Engine Compartment E-box
- Tighten the nuts -6 and 7- to 4.5 Nm.
- Tighten the nuts -3, 4 and 5- to 6 Nm.
Overview - Instrument Panel Relay Carrier/Fuse Carrier and A-Pillar Relay Carrier/Fuse Carrier
1 - Vehicle Electrical System Control Module -J519-
- Component location overview. Refer to → Chapter "Component Location Overview - Control Modules".
2 - Mount
- For the relay and fuse panel control module
- Removing and installing. Refer to → Chapter "Relay/Fuse Carrier Mount with Vehicle Electrical System Control Module -J519-, Removing and Installing".
3 - Relay Carrier Under Left Instrument Panel
- Removing and installing. Refer to → Chapter "Relay Carrier, Under Instrument Panel on Left Side, Removing and Installing".
4 - Front Parking Aid Warning Buzzer -H22-
- Overview. Refer to → Chapter "Overview - Parking Aid".
5 - Vehicle Positioning System Interface Control Module -J843-
- Removing and installing. Refer to → Body Exterior; Rep. Gr.57; Central Locking; Central Locking Component Location Overview.
6 - Nut
- 4.5 Nm
- Quantity: 2
7 - Vehicle Electrical System Control Module Relay Panel
- Removing and installing. Refer to → Chapter "Relay Carrier on Vehicle Electrical System Control Module, Removing and Installing".
8 - Screw
- 2.5 Nm
- Quantity: 2
9 - Fuse Panel C -SC-
- Removing and installing. Refer to → Chapter "Fuse Panel C -SC-, Removing and Installing".
10 - Mount
- For 16-Pin Connector -T16-
READ NEXT:
E-Box, Removing and Installing
Removing
- Remove the relay and fuse panel and move them to the side
with the wires still connected. Refer to
→ Chapter "Relay and Fuse Panel B -SB- in the E-Box, Removing
and Insta
Relay and Fuse Carriers Behind Instrument Panel on Driver Side, Removing and
Installing
Relay Carrier on Vehicle Electrical System Control Module, Removing and
Installing
Removing
- Remove the driver side instrument panel cover. Refer to
→ Body Interior; Rep. Gr.68;
Control Modules
Component Location Overview - Control Modules
Component Location Overview - Control Modules
1 - Vehicle Electrical System Control Module -J519-
Removing and installing. Refer to
â†SEE MORE:
Starting and stopping the engine automatically
Applies to: vehicles with Start/Stop system
The system checks if certain conditions are met
before and during the Stop phase, and determines
if the engine stops and how long it remains
stopped. For example, if power usage is
high, the engine will not be stopped. Along with
other conditions, the foll
Door, Removing and Installing
Removing
- Disconnect the door connector on the A-pillar. Refer to
→ Electrical Equipment; Rep. Gr.97; Connectors.
Note
Secure the A-pillar in the area of the door arrester using
adhesive tape, so that the paint will not be damaged.
- Remove the door arrest