Audi Q3 Owners & Service Manuals

Audi Q3: ESD Work Surface -VAS6613-

Electrical Equipment General Information / Electrical System / Audi Q3 (8U) 2011-2018 Service Manual / ESD Work Surface -VAS6613-

ESD Work Surface -VAS6613-, Using

  • The electro-static discharge ESD Work Surface -VAS6613- protect electronic components from getting damaged by an electro-static charge.
  • This makes is possible to perform repairs on sensitive electronic components on an open mat.
  • For more information as to what work can be performed on the ESD Work Surface -VAS6613-. Refer to the "Electrical Equipment" chapter in the repair manual.

- Place the electro-static discharge mat -3- from ESD Work Surface -VAS6613- on a clean, dry table.

- Connect the Ground (GND) -2- to one of the buttons on the mat.

- Connect the GND connector adapter -1- to the adapter connector on an outlet with contact protection or connect the alligator clip to a ground in the building or a water pipe.

- Connect the wrist strap -4- to one of the buttons on the mat.

- Attach the wrist strap directly to your wrist - never to your shirt sleeve or jacket sleeve.

  Caution

If working on especially sensitive electronic component and with the pad exposed, use only non-magnetic tools, for example, a Wrench - Driver -T10072-.

Audi Q3. A96-10814

Special Tools

Special tools and workshop equipment required

  • Torque Wrench 1331 5-50Nm -VAG1331-

Audi Q3. W00-0427

  • Wiring Harness Repair Set -VAS1978A-

Audi Q3. W00-10400

  • Wiring Harness Repair Set -VAS1978B-

Audi Q3. W00-10782

  • Adjust the sliding stop in the Wiring Harness Repair Set - Wire Strippers -VAS1978/3- pliers jaws to 12 to 14 mm for the wire to be stripped.

Audi Q3. N97-0016

  • To press the crimp connector, use the Wiring Harness Repair - Crimping Plier - Base Tool -VAS1978/1-2- with Wiring Harness Repair - Crimping Head - .35-2.5mm -VAS1978/1-1-.

Audi Q3. N97-10491

  • Wiring Harness Repair Set - Hot Air Blower -VAS1978/14A- from the Wiring Harness Repair Set -VAS1978B-
  • Wiring Harness Repair - Blower - Shrink Element -VAS1978/15A- from the Wiring Harness Repair Set -VAS1978B-
  • Wiring Harness Repair Set VAS 631 003 -VAS631003-

Audi Q3. W00-10782

  • Release Tool Set -VAS1978/35-

Audi Q3. W00-10402

  • Fiber Optic Repair Set -VAS6223B-

Audi Q3. W00-10202

  • Hose Cutting Pliers -VAS6228-

Audi Q3. W00-10022

  • Contact Surface Cleaning Set -VAS6410-

Audi Q3. W00-10546

  • -1- Adapter wire, for connection to radio; length: approximately 30 cm
  • -2- Connecting wire, available in various lengths
  • -3- Adapter wire, for connection to antenna; length: approximately 30 cm
  • Contact Surface Cleaning Set -VAS6410-
  • Aerial Cable Repair Set -VAS6720-
  • Wiring Harness Repair - Blower - Shrink Element -VAS1978/15A- from the Wiring Harness Repair Set -VAS1978B-
  • Wiring Harness Repair Set -VAS631001-

Audi Q3. N97-0424

Revision History

DRUCK NUMBER: A005AA00421

Audi Q3. Revision History

READ NEXT:

  Radio Installation Instructions

Retrofitting Radio Systems General Information Before installing radios and telephone systems (radio systems), disconnect the negative terminal of the Battery -A-. Refer to →Electrical Equip

  Heating, Ventilation & Air Conditioning

  General, Technical data

SEE MORE:

  Setting the distance

Applies to: vehicles with adaptive cruise assist Fig. 102 Operating lever: setting the distance When approaching a vehicle driving ahead, the adaptive cruise assist brakes to the set speed and then maintains the set distance. If the vehicle driving ahead accelerates, then the adaptive cruise assist

  Lower Control Arm, Removing and Installing

Special tools and workshop equipment required Locating Pins -T10096- Torque Wrench 1332 40-200Nm -VAG1332- Removing - Before starting work, determine the measurement -a-, for example with tape measure, from center of wheel to lower edge of wheelhouse.   Note Measurement

© 2019-2026 Copyright www.auq3.net | 0.0103